Candles Trend EMA
-
Hi!
How can I describe two candles (second last, active whithout a wick in the trend) in the trend with EMAS?
Candles under the EMAS for short.
Candle size second last X pips
Candle size active X pips, without a wick
…the same as in the picture…
Thank you!!!
-
please explain better. also all those cnadles have a wick. but on here the currently forming or active candle would be candle ID 0 and previous will be ID 1 in the condition paramters
-
on this pic can u show where you would like to enter?
-
Hello!
Sorry, you are right...i don´t saw the wick in the trend direction....the last candle without a wick in trend direction.
The entry is the yellow arrow....
I understood, that the active candle is ID0...
The second last ID1...how can i describe, i say it with my words (sell example...buy the other way around):
The description is for one timeframe...i need the same check for 3 different timeframes (adjustable) (start is with H2/H1/M15 example)- look at the body of the ID1 candle, it should be a body size of X pips (adjustable)
- look if the candle is in down trend under the 3 EMAS (adjustable)
- look that the last candle ID0 have minimum X pips (adjustable)
- look if the candle ID0 active is started minimum at the half body size of the candle with ID1 or further below (look at the picture the start of the active candle was under the 50% line of the second last candle).
- the active candle with ID0 don´t have to be a wick in the trend direction
- when all checks are ok, go to the next lower timeframe and check the same
- the same as 6. and open a sell trade
(doesn´t fit a check in one point..stop the check and go to the beginning)
I hope now it easier to understand...
It give a lot of possibilities....loops...if...normal conditions...and i don´t know, which is correct...Thank you!
-
bro... still confusing. wat is a 50 % line? and second last candle? and wat is started minimum at half body size? each candle starts ate open price ate the close of ID 1 candles
-
all candles that are actively forming you cant be sure it will have no wick untill its closes so that cannot be measured. u can only measure historical candle wicks
-
Second last candle = penultimate/next to last/last but one…sorry I am not a native speaker.
50% you see the line in the picture..on this line should be Start the active candle, but not over this line (adjustable).
-
I know but we speak here of the active candle and when a lot of pressure in the trend, you don’t have a wick in the active candle in the direction of the trend.
-
there is a wick. can you draw on the pic to show. all i see is candle bearish closing below ema, nothing specific
-
which of those 3 bearish candles are you trying to measure?
-
Look at the picture. Blue marked.
Candle ID1
Candle ID0
…and both candles should be under the EMAS 233/55/21 exponential. -
-
okay so u wannt a sell entry if 0 candle goes up 50% D id 1? AND that candle needs to be a certain pips
-
have u strarted any block on this project?
-
no, because this is the start...and i don´t know...what is correct and how can i solve this...loops, if....
-
@flyfisher use condition block and look ate the parameters you should see candle modification there
-
https://fxdreema.com/shared/kpAzTKNXc
Hi!
....i started the project...
..but my problem is...how can i insert my other conditions...? (i heard that candle ID0 is not a good solution...i use ID1 for the current active candle).
Following description is for sell:
- 2 candles in a row for sell trend
- all both candles should be under the 3 EMAS (adjustable) in sell direction
- the current candle ID1 lower low as the second last candle ID2
- the second last candle ID2 should have to be a body size with X pips (adjustable)
- current candle ID1 should have to be a body size with X pips (adjustable) and without a wick in sell trend; the candle started minimum at the half body size of the candle ID2 or further below...picture with 50% line)
- when all checks ok, than to the next lower timeframe and check the same...i think here the same procedure...
How can i do this?....loops...and....sorry, i don´t know and i hope anyone can help me....
Thank you!
-
@flyfisher so you have created everything except number 2 condition and number 5
-
where do u need help u are doing good. also after this then you can con tinue to connection conditions the same for the smaller timeframe
-
I don’t have the knowledge…that is the reason why I asked.
How can I insert now the other conditions…lower low?
Is this correct?
How can I insert the candle body sizes and the wick condition?
Thank you!
