Posts made by ambrogio

@xburbx It's right for me. You have a very tight Take Profit, set TP 100 and you can see on the chart

@saadatfx you're welcome!

@saadatfx the same as my picture above.

@saadatfx i can see you connected both break even and trailing on the buy side only

@saadatfx 10 pips BE, +10 pips trail start=20 pips, trailstop 5, step 5

@miguel33 like this??

https://fxdreema.com/forum/topic/23097/buy-only-sell-only-mt5/5?_=1760013562831

@Campero

@Campero you are actually filtering trades by group number, you should instead select manually (or all automated and manual)

@xburbx From what I understand, it looks for price levels on past candles. You're working on a daily basis. In my opinion, the time frame is too high. I tried playing with these values ​​on M1 and it works. It's just a matter of setting.

@merajmusic I would do this

@MT4Nutzer you are welcome!

@MT4Nutzer Virtual stops should disappear on their own when triggered, if you are closing trades manually instead, double click on the line => delete

@xburbx said in ORB Not Triggering Short Trades:

-Thanks. I wouldn't use pips though for my stop loss/target on this. I would need it to work off of percentage of price for target and stop. <<ok, pay attention for invalid price>>

-For the 'once a day' tab you have 10:00-10:05. Does that mean it will only look for trades within that time period? The trade itself should be allowed to show up anytime up until 16:00. <<you can extend the time range till 16:00>>

-In your condition bar, the time stamp is 9:30. I thought it was based on the 10:00 as the ending bar range from 9:30-10? <<yes because at 10:00 the M30 candle at 09:30 time stamp is completely formed, so you can check the high and low>>

@xburbx This is what I mean, starting from your initial project. Be careful when working with candlestick levels, as you'll often get invalid price or invalid stop-loss errors (your pending orders gave me those errors). For simplicity, I used pips.

@xburbx said in ORB Not Triggering Short Trades:

Why is this only triggering long trades and not short trades? I have both longs and shorts setup the same.

Shared FXDreema File

You're asking at 9:30 to check the M30 high/low candlestick at the 9:30 timestamp. I think this is incorrect. At that time, the candlestick is starting, and the only available price is the M30 open price, so the ask price is always > , but the bid price is never < itself. I think you should check the 9:30 candlestick at 10:00 at least.

@javi0030 said in Me sale este error: '|' - illegal operation use:

Es extraño, pero ya solucioné ese tema, como? no lo se, simplemente borre ese bloque y lo volvi a montar desde cero. Y para que el bot abra nuevas posiciones de las mismas, reemplace unos bloques, por "for each trade" y funciona. Muchas gracias por su ayuda!! saludos!!

good!

@abodyfit put candle ID1

i suggest you to put these variables in a "comment" block (under a "pass" block) and see on chart what happens. I think there is a mistake in the project's logic.

@javi0030 said in Me sale este error: '|' - illegal operation use:

https://fxdreema.com/shared/zgtcNn6hc

Disculpa, creo que ahora si podras ver el proyecto. Muchas gracias

Saludos

Inside blocks 162 and 157, put == instead of =

@KARUBANGA said in Help with adding an input of "Applied Price" to "WILLIAM PERCENTAGE RANGE INDICATOR":

Hye guys I am in need of help now to add the input of "APPLIED PRICE "-Open Price to the mt5 indicator of William percentage range

It's not possible, basically it's a price range calculated on the highs and lows of the period, this is the formula:

Also the indicator itself only shows the period to choose